【SIP PERFORMANCE】 メインハーネス SIP PERFORMANCE

Preparation for SIP Rev Counter
for 4-pin Ignition Lock，for 12V AC Horn (buzzer)

バイク用配線パーツや工具をお探しなら【エーモン】のMOTOLECTIONシリーズはこちら
Circuit diagramsはこちら
Circuit diagramsはこちら

※取扱説明書が付属する場合は外国語となります。
※輸入商材の為、納期が遅れる場合がございます。あらかじめご了承ください。
※画像には他の商品が含まれている場合があります。
※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。

The introduction of the SIP PERFORMANCE Wiring Loom series closes a gap between many other SIP PERFORMANCE components.
If you install a SIP Speedometer/Rev Counter and a SIP PERFORMANCE by VAPE Ignition，you can use the matching SIP PERFORMANCE Wiring Loom to connect almost all of the Speedometer and Ignition connections plug ＆ play.
No more searching for the right Wire - e.g.
for the speedometer power supply.
Perfect plug ＆ play solution
High-quality production Made in Germany
Fully prepared system
The “Wiring Loom SIP PERFORMANCE for conversion to electric Ignition SIP PERFORMANCE by VAPE (AC)” is designed for Vespa P80-150X / PX80-200E / Lusso 1° / P200E and is intended for concepts without a Battery.
The system works with 12V AC and is prepared for parking / high / low beam and Brake Light as well as 4-way Indicators.
The design is also adapted for a 4-pin Ignition Lock and a 12V AC Horn (buzzer).
The AC variant is deliberately designed as an alternating current concept without a battery - a subsequent conversion to full DC is therefore not possible.
In this case，please use the appropriate DC versions of the Wiring Loom.
For the PX models，the power supply for the speedometer black box is provided in the rear vehicle area under the spare wheel so that the speedometer peripherals can be neatly integrated there.
Plug ＆ Play preparation for the VAPE Voltage Regulator; optionally available Wiring for connection to a Ducati/Classic VAPE Voltage Regulator.
Plug ＆ Play preparation for the SIP Fast-Flow Fuel Tap
No Battery，no later conversion to Full-DC possible
Connection of Control Lights and Ignition Lock via Premium Wiring (included)
Designed for 4 Indicators and Indicator Switch with 6 wires
Recommendation for direct Speedometer control integration：SIP Indicator Switch with Speedometer button
Preparation for Light Switch with 9 wires
Designed for 12V AC Horn (buzzer)
Provision for 3-pole AC Indicator Relay 12V：item no.
85036000 or 85030000
Preparation for Wire Brake Light Switch on Steering Head for solutions with fully hydraulic Disc Brake：If this is not required，the plugs at the Wire ends must be securely insulated to prevent contact with metal in the Steering Head.
The Brake Light Switch on the foot brake pedal must be designed as a “Lock”，e.g.
item no.
18187810 or 18187800
The protective hose for the areas running inside the chassis is deliberately designed with a larger diameter.
This allows the Wiring Loom to be flattened to suit the space available when passing through the Frame below the Steering Head - this makes installation much easier.
Caution：Always handle the plugs for the SIP Speedometer/Rev Counter with extreme care and never pull in the Wiring Loom using these plugs or cables.
The cables have a cross-section of only 0.5 mm and - like the plugs - are not designed to withstand high tensile forces.
The black ground cable to the Engine with 6 mm eyelet must be connected to the VAPE CDI - either directly to the CDI or to the Crankcase (depending on the CDI/ground setup).
A separate ground cable is recommended.
Conclusion：The right plug ＆ play solution for a tidy PX electrical system with SIP PERFORMANCE by VAPE (AC) - without a Battery and without searching for cables.
SIP Cable Kit SIP
USB Charger charging socket SIP

ユーザのインプレッションを見る

適合車種： PX150、PX125、P125X、PX125E、PX125E Arcobaleno、P150X、P200E、PX200E、PX150E ( 適合車種を見る )