【SIP PERFORMANCE】 メインハーネス SIP Performance フルトラ点火へのコンバージョン用 SIP PERFORMANCE VAPE AC

Preparation for SIP Rev Counter
w/o battery
with high-/low beam and brake light
indicator handlebar end
12V AC
for 9-pin Ignition Lock
Grade 1＊ - first-class repair and for tuned engines

バイク用配線パーツや工具をお探しなら【エーモン】のMOTOLECTIONシリーズはこちら
Circuit diagramsはこちら
Circuit diagramsはこちら
Technical tipsはこちら

※取扱説明書が付属する場合は外国語となります。
※輸入商材の為、納期が遅れる場合がございます。あらかじめご了承ください。
※画像には他の商品が含まれている場合があります。
※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。

With the introduction of the SIP PERFORMANCE wiring harness range，we are closing a gap between many other SIP PERFORMANCE parts.
If you buy a SIP Speedometer/Rev Counter and a SIP PERFORMANCE VAPE Ignition for your scooter，you can use a SIP PERFORMANCE Wiring Loom to connect almost all the connections of the Speedometer/Rev Counter or Ignition via plug-and-play.
This eliminates the tedious search for the right Wire，e.g.
for the speedometer power supply.
Plug ＆ Play for SIP Speedometer/Rev Counter ＆ SIP PERFORMANCE VAPE
Handmade in Germany with Wire from German production
Sophisticated AC system for an optimal setup
The AC variants of the SIP PERFORMANCE wiring looms are designed for concepts without a Battery.
Subsequent conversion to direct current (full DC) is not possible.
In this case，please use the DC versions of the Wiring Loom.
This Wiring Loom provides the power supply for the speedometer black box in the rear part of the scooter，in the area of the Rectifier under the spare wheel.
Vespa 180 Rally and 180 SS：
This Wiring Loom is intended for Models with Ignition Lock.
For Models without Ignition Lock please use one of the following Wiring Looms：
AC version：86134200
DC version：861343DL
Device for the speedometer button/switch with the SIP Light Switch.
The Wiring still required for this is not part of the scope of delivery.
Plug-and-play preparation for the SIP fast-flow Fuel Tap
Plug-and-play preparation for the VAPE Voltage Regulator; optionally available wiring harness for connecting the Wiring Loom to a Classic VAPE Voltage Regulator
Plug-and-play preparation for temperature or lambda sensor
Without Battery
Handlebar end indicators：Wire from Indicator Switch to indicators is included
12V buzzer (no Horn)
Device for a 2-pole AC Indicator Relay for 12 V
Wire ends for ground and parking light on the Headlight Unit are fitted with 4 mm round plugs for the rectangular headlight.
For models with a round Headlight Unit，the enclosed 4.8 mm flat sockets must be crimped onto these two wires.
The protective tube to the Rear Light is split in two (brown Adhesive Tape).
For very old scooters with a welded-in tube to the Rear Light，one half of the protective tube can be removed without running the risk of damaging the strands with a cutter.
The Brake Light Switch on the foot brake pedal must be a “Lock” version，e.g.
article 18187810 or 18163710.
The protective tubing for the parts of the Wiring Loom that run inside the chassis was deliberately chosen with a larger diameter.
This allows the Wiring Loom to be adapted to the dimensions in the Frame when passing through the Frame below the Steering Head，which makes installation much easier.
The Wiring Loom comes with a small Wire (blue cable)，which can optionally be used to supply power to the Handlebar Control Light and/or the lighting of a standard speedo.
Caution：Always handle the plugs for the SIP Speedometer/Rev Counter with extreme care and never pull in the Wiring Loom on these plugs or cables.
These wires only have a cross-section of 0.5 mm² and - like the plugs - are not designed to absorb large forces.
Fitting the earth cable of the Wiring Loom (black cable with 5 mm eyelet) in the Steering Head together with the earth connection of the Steering Head wiring harness (black cable with 5 mm eyelet) to ensure a correct earth connection.
The black ground cable to the Engine with 6 mm eyelet must be connected to the VAPE CDI：either Screw directly to the CDI or screw to the Crankcase if the CDI is equipped with the SIP ground cable.
We generally recommend installing the separate SIP ground cable.
With the corresponding wiring harness，a VAPE Classic Voltage Regulator can be installed without having to re-crimp the plugs.
Conclusion：The perfect plug-and-play solution for all those who don’t want to delve deeper into scooter electrics but prefer to “plug together” according to instructions.
Light Switch SIP Conversion
Brake Light Switch
Ignition Lock SIEM

ユーザのインプレッションを見る

適合車種： 180SS、180Rally ( 適合車種を見る )