Set， Switch Gear and Throttle Housing， Assy. RC36-2， RC30 Style.

Following Items ：
Housing， Throttle， Lower ( x 1 )
Housing， Throttle， Upper ( x 1 )
Screw， Pan， 5X20 ( x 2 )
Harness Extension， Switch Assembly， Starter， RC36-2， RC30 Style ( x 1 )
Harness Extension， Switch Assembly， Winker， RC36-2， RC30 Style ( x 1 )
Switch Assembly， Starter ( x 1 )
Switch Assembly， Winker， NC30 ( x 1 )
※画像はイメージです。
※取扱説明書が付属する場合は外国語となります。
※輸入商材の為、納期が遅れる場合がございます。あらかじめご了承ください。
※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。
Set， Switch Gear and Throttle Housing， Assy. RC36-2， RC30 Style.
To update and improve the look of the RC36-2， RC30 Tribute， we recommend fitting our TYWH-0010 Switch Assembly， Starter product and TYWH-0009 Switch Assembly， Winker， NC30 product. This switch gear is not directly compatible with the RC36-2 wire harness， so we have designed harness extensions TYWH-0011 and TYWH-0012 that simply plugs inline between the switch gear and the RC36-2 main harness， with no modifications to either the switch gear connections or the main RC36-2 connections required.
Note that this set has only been tested on the RC36-2 in RC30 Tribute spec. It will not fit the standard RC36-2 due to connector positions， wire lengths etc. without additional modifications.
Please see the fitting instructions for the routing of the wires and the extension harness. Note that this is only relevant to the RC36-2 when fitted with our RC30 Tribute bodywork kit and wiring.

Honda OEM throttle housing is included to complete the modification.

Switch Assy， Winker Functions：

The main headlights can now be switched off， unlike the standard RC36-2. However， the small running lights in the NC30 headlights used in the RC30 Tribute kit remain illuminated permanently due to being on a different circuit.
Note that due to the standard RC36-2 wiring， the tail light will stay on permanently when the ignition switch is ON. Only the headlights are turned on and off with the switch gear. The tail light is unaffected by the switch position and will be always on.
The ‘OFF’ and ‘P’ positions of the headlight switch have the same function. The headlight is off.
With the headlight in the ‘H’ position， the headlight is on.
Turn signal switch works as normal.
Hi-Lo switch works as normal.
The clutch switch works as normal.
Horn switch works as normal. ＊Please see fitting instructions on special grounding required for the horn.＊
Passing light switch is an additional function that is not available on the RC36-2 standard switch gear. Flick the switch for momentary high beam.


Switch Assy， Starter Functions：

RUN/OFF switch works as normal.
While the RUN/OFF switch is in the OFF position， pressing the start button has no effect. The engine will not turn over and the headlights (if switch on) will stay illuminated.
While the RUN/OFF switch is in the RUN position， pressing the start button has two functions. The engine will turn over and start， and the headlights (if switched on) will be switched off via a relay to allow full battery power to be sent to the starter motor. This is the same function as the standard RC36-2.
The brake light switch works as normal.


Also note If using the TYWH-0013 switch gear on your RC36-2 RC30 Tribute build， or just as a replacement for the original RC36-2 switch gear then please note that this switch gear does not allow fitment of the OEM RC36-2 choke lever. You would need to use an alternative method for actuating the choke， such as using TYPP-0033 choke cable and BPSY-0353 Stay， which could be mounted in a convenient position.

ユーザのインプレッションを見る

適合車種： VFR750F ( 適合車種を見る )